Engine Controls and Fuel - 3.0L LM2 Diesel | Diagnostic Information and Procedures | Document ID: 5501031
DTC P0097-P0099, P00F4-P00F6, or P0112-P0114
Diagnostic Instructions
Perform the Diagnostic System Check prior to using this diagnostic procedure: Diagnostic
System Check - Vehicle
Review the description of Strategy Based Diagnosis: Strategy Based Diagnosis
An overview of each diagnostic category can be found here: Diagnostic Procedure
Instructions
DTC Descriptor
DTC P0097
Intake Air Temperature Sensor 2 Circuit Low
DTC P0098
Intake Air Temperature Sensor 2 Circuit High
DTC P0099
Intake Air Temperature Sensor 2 Circuit Intermittent
DTC P00F4
Intake Air Relative Humidity Sensor Circuit Low
DTC P00F5
Intake Air Relative Humidity Sensor Circuit High
DTC P00F6
Intake Air Relative Humidity Sensor Circuit Erratic
DTC P0112
Intake Air Temperature Sensor Circuit Low
DTC P0113
Intake Air Temperature Sensor Circuit High
DTC P0114
Intake Air Temperature Sensor Circuit Intermittent
Diagnostic Fault Information
| Circuit |
Short to Ground |
Open/High Resistance |
Short to Voltage |
Signal Performanc |
| Ignition |
P0102, U060F, U1346* |
P0102, U060F, U1346* |
— |
— |
| Serial Data |
U060F, U1346 |
U060F, U1346 |
U060F, U1346 |
— |
| Ground |
— |
P0102 |
— |
— |
| * Additional DTCs may set |
|
|
|
|
Typical Scan Tool Data
Intake Air Temperature Sensor & Intake Air Temperature Sensor 2
Short to
Short to
Circuit
Ground
Open
Voltage
Operating Conditions: Engine = Idling
| Circuit |
Short to Ground |
Open |
Short to Voltage |
| Parameter Normal Range: −39 to 149°C (−38 to 300°F) |
|
|
|
| Ignition |
−40°C (−40°F) |
−40°C (−40°F) |
— |
| Serial Data |
−40°C (−40°F) |
−40°C (−40°F) |
−40°C (−40°F) |
| Ground |
— |
−40°C (−40°F) |
— |
Ambient Humidity
| Circuit |
Short to Ground |
Open |
Short to Voltage |
| Operating Conditions: Engine = Idling Parameter Normal Range: 5 to 95% |
|
|
|
| Ignition |
0% |
0% |
— |
| Serial Data |
0% |
0% |
0% |
| Ground |
— |
0% |
— |
Circuit/System Description
| Circuit |
Description |
| Ignition |
Supplied from a fuse. |
| Serial Data |
Digitally encoded information for communication between devices. |
| Ground |
Chassis Ground |
|
Component |
Description |
|
|
B75 Mass Air Flow Sensor |
The assembly has several functions: The mass air flow sensor is a hot film type sensor that measures the mass of air (not the volume) entering the engine. The signal varies with engine load and is displayed by the scan tool in Hertz (Hz) and grams per second (g/s). The component houses the following sensors: – Barometric Pressure Sensor 2 – Intake Air Temperature Sensor – Intake Air Temperature Sensor 2 |
|
| Component |
Description |
| K20 Engine Control Module |
The control module contains a microprocessor used to process input data to control outputs. The control module controls a series of actuators to ensure optimal engine performance. The control module does this by reading values from a variety of sensors, interprets the data and adjusts the engine actuators accordingly. |
Conditions for Running the DTC
P0097, P0098, P0099, P00F4, P00F5, P00F6
DTC P1682, P16A7, P16BC = Not set
Ignition and Start Switch Signal = On
Ignition and Start Signal = Greater than 11 V
LIN Bus = Enabled
Frequency the DTC runs = Continuously — After the running conditions are met
P0112, P0113, P0114
DTC P14B6, U060F, U1346, U2011 = Not set & Not pending
Ignition and Start Switch Signal = On
Ignition and Start Signal = Greater than 8.5 V
LIN Bus = Enabled
Frequency the DTC runs = Continuously — After the running conditions are met
Conditions for Setting the DTC
P0097
- Ignition » On / Vehicle » In Service Mode
- Verify DTC P0097, P0098, P0099, P00F4, P00F5, P00F6, P0112, P0113, P0114, U060F, U1346
is not set.
⇒ If only DTC P0097, P0098, P0099, P00F4, P00F5, P00F6, P0112, P0113, P0114 is set
Replace the component: B75 Mass Air Flow Sensor
⇒ If DTC U060F, U1319, U1346 is set and other DTCs are set
Refer to: DTC P0102, P0103, U060F, or U1319
⇓ If no DTC is set
- Verify the scan tool parameter: Intake Air Temperature Sensor & Intake Air Temperature
Sensor 2 = The value should not spike or drop out.
Perform the action while monitoring the parameter:
Wiggle the harness and connector: B75 Mass Air Flow Sensor
Wiggle the harness and connector: K20 Engine Control Module
⇒ If the value spikes or drops out
Repair as necessary » Wiring / Terminal(s) / Electrical Connector(s)
⇓ If the value does not spike or drop out
- Operate the vehicle within the Conditions for Running the DTC. You may also operate the
vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Verify the DTC does not set.
⇒ If the DTC sets
Repeat step 2
⇓ If the DTC is not set
- All OK.
Repair Instructions
Perform the Diagnostic Repair Verification after completing the repair: Diagnostic Repair
Verification
Mass Airflow Sensor with Intake Air Temperature Sensor Replacement — B75 Mass Air Flow
Sensor
For control module replacement, programming, and setup refer to: Control Module
References
Additional Procedures
Barometric Pressure Sensor Reset — Perform only when the following component/system is
replaced or serviced:
B75 Mass Air Flow Sensor — Replaced
K20 Engine Control Module — Replaced