Skip to content
Tahoe / Yukon Service Manual

DTC B107E or B107F

Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptors DTC B107E Passenger Door Lock Switch Lock Control DTC B107F Passenger Door Lock Switch Unlock Control Symptom Byte Information: Symptom Byte List Diagnostic Fault Information

Circuit number Circuit Function Short to Ground Open/High Resistance Short to Voltage Signal Performan
2773 Signal B107E 23 1 1 —
2774 Signal B107F 23 2 2 —
1250 Ground — 3 — —
1. Door Lock Switch Lock Inoperative 2. Door Lock Switch Unlock Inoperative 3. Passenger Door Lock Switch Inoperative

Circuit/System Description The S79P Front Side Door Window Switch-Passenger provides the S13P Door Lock Switch- Passenger with signal circuit 2773 and signal circuit 2774. Ground is applied at all times to the S13P Door Lock Switch-Passenger. When the lock switch or unlock switch is pressed, ground is applied to the S79P Front Side Door Window Switch-Passenger through signal circuit 2773 or signal circuit 2774. Conditions for Running the DTC The system voltage is 9–16 V. Conditions for Setting the DTC B107E 23 Circuit 2773= Short to Ground— For greater than 60 s . B107F 23 Circuit 2774= Short to Ground— For greater than 60 s . Action Taken When the DTC Sets B107E 23 The lock request will be ignored and the doors will not lock when using the passenger door lock switch. B107F 23 The unlock request will be ignored and the doors will not unlock when using the passenger door unlock switch. Conditions for Clearing the DTC The DTC will be current for as long as the fault is present. When the fault is no longer present, the DTC will be a history DTC. A history DTC will clear after 40 ignition cycles. Reference Information Schematic Reference Door Lock/Indicator Schematics Connector End View Reference Master Electrical Component List Description and Operation Power Door Locks Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Verification

  1. Vehicle in Service Mode.
  2. Verify the scan tool Right Front Door Interior Lock Status and the Right Front Door Interior Unlock Status changes from Inactive to Active while pressing the S13P Door Lock Switch - Passenger » Lock Switch & Unlock Switch ⇒ If a parameter does not change Refer to Circuit/System Testing ⇓ If the parameters change from Inactive and Active
  3. A fault is not currently present and may be an intermittent condition Circuit/System Testing
  4. Vehicle OFF and all vehicle systems OFF, disconnect the harness connector at the S13P Door Lock Switch-Passenger.
  5. Verify a test lamp illuminates between ground circuit terminal 4 and B+. ⇒ If the test lamp does not illuminate 2.1. Repair the open/high resistance on circuit 1250 or the ground connection. ⇓ If the test lamp illuminates
  6. Ignition » On / Vehicle » In Service Mode
  7. Verify the scan tool Right Front Door Interior Lock Status parameter is Inactive ⇒ If not Inactive 4.1. Test the circuit 2773 for a short to ground ⇒ If a short to ground is found, repair the fault on the circuit. ⇓ If a short to ground is not found. 4.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇓ If Inactive
  8. Install a 3 A fused jumper wire between the signal circuit terminal 2 and ground.
  9. Verify the scan tool parameter is now Active. ⇒ If not Active and the 3 A fuse is OK 6.1. Test the circuit 2773 for an open/high resistance. ⇒ If an open/high resistance is found, repair the fault on the circuit. ⇓ If an open/high resistance is not found. 6.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇒ If not Active and the 3 A fuse is open 6.1. Test the circuit 2773 for a short to voltage. ⇒ If a short to voltage is found, repair the fault on the circuit. ⇓ If a short to voltage is not found. 6.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇓ If Active
  10. Verify the scan tool Right Front Door Interior Unlock Status parameter is Inactive ⇒ If not Inactive 7.1. Test the circuit 2774 for a short to ground ⇒ If a short to ground is found, repair the fault on the circuit. ⇓ If a short to ground is not found. 7.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇓ If Inactive
  11. Install a 3 A fused jumper wire between the signal circuit terminal 3 and ground.
  12. Verify the scan tool parameter is now Active. ⇒ If not Active and the 3 A fuse is OK 9.1. Test the circuit 2774 for an open/high resistance. ⇒ If an open/high resistance is found, repair the fault on the circuit. ⇓ If an open/high resistance is not found. 9.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇒ If not Active and the 3 A fuse is open 9.1. Test the circuit 2774 for a short to voltage. ⇒ If a short to voltage is found, repair the fault on the circuit. ⇓ If a short to voltage is not found. 9.2. Replace the S79P Front Side Door Window Switch-Passenger. ⇓ If Active
  13. Replace the S13P Door Lock Switch-Passenger. Component Testing Door Lock Switch
  14. Vehicle OFF, disconnect the harness connector at the S13P Door Lock Switch - Passenger.
  15. Test for infinite resistance between the signal terminal 2 and the ground terminal 4 with the switch not pressed. ⇒ If less than infinite resistance Replace the S13P Door Lock Switch - Passenger. ⇓ If infinite resistance
  16. Test for infinite resistance between the signal terminal 3 and the ground terminal 4 with the switch not pressed. ⇒ If less than infinite resistance Replace the S13P Door Lock Switch - Passenger ⇓ If infinite resistance
  17. Test for less than 2 Ω between the signal terminal 2 and the ground terminal 4 with the switch in the Lock position. ⇒ If 2 Ω or greater Replace the S13P Door Lock Switch - Passenger. ⇓ If less than 2 Ω
  18. Test for less than 2 Ω between the signal terminal 3 and the ground terminal 4 with the switch in the Unlock position. ⇒ If 2 Ω or greater Replace the S13P Door Lock Switch - Passenger. ⇓ If less than 2 Ω
  19. All OK Repair Instructions Perform the Diagnostic Repair Verification after completing the repair. Door Lock Switch Replacement - Passenger Front Front Side Door Window Control Switch Replacement